TRF7970A
SLOS743K – AUGUST 2011 – REVISED APRIL 2014
www.ti.com
The relation between the 3-bit code and the external RF field strength (A/m) sensed by the antenna must
be determined by calculation or by experiments for each antenna design. The antenna Q-factor and
connection to the RF input influence the result. Direct command 0x19 is used to trigger an Internal RSSI
measurement.
For clarity, to check the internal or external RSSI value independent of any other operation, the user must:
1. Set transmitter to desired state (on or off) using Bit 5 of Chip Status Control register (0x00) and enable
receiver using Bit 1.
2. Check internal or external RSSI using direct commands 0x18 or 0x19, respectively. This action places
the RSSI value in the RSSI register.
3. Delay at least 50 μs.
4. Read the RSSI register using direct command 0x0F; values range from 0x40 to 0x7F.
5. Repeat steps 1-4 as desired, as register is reset after it is read.
6.6
Oscillator Section
The 13.56-MHz or 27.12-MHz crystal (or oscillator) is controlled by the Chip Status Control register (0x00)
and the EN and EN2 terminals. The oscillator generates the RF frequency for the RF output stage as well
as the clock source for the digital section. The buffered clock signal is available at pin 27 (SYS_CLK) for
any other external circuits. B4 and B5 inside the Modulation and SYS_CLK register (0x09) can be used to
divide the external SYS_CLK signal at pin 27 by 1, 2 or 4.
Typical start-up time from complete power down is in the range of 3.5 ms.
During Power Down Mode 2 (EN = 0, EN2 = 1) the frequency of SYS_CLK is switched to 60 kHz (typical).
The crystal needs to be connected between pin 30 and pin 31. The external shunt capacitors values for C 1
and C 2 must be calculated based on the specified load capacitance of the crystal being used. The external
shunt capacitors are calculated as two identical capacitors in series plus the stray capacitance of the
TRF7970A and parasitic PCB capacitance in parallel to the crystal.
The parasitic capacitance (C S , stray and parasitic PCB capacitance) can be estimated at 4 to 5 pF
(typical).
As an example, using a crystal with a required load capacitance (C L ) of 18 pF, the calculation is shown in
Equation 1 .
C 1 = C 2 = 2 × (C L – C S ) = 2 × (18 pF – 4.5 pF) = 27 pF
A 27-pF capacitor must be placed on pins 30 and 31 to ensure proper crystal oscillator operation.
C S
TRF7970A
(1)
Pin 30
C 1
Crystal
Pin 31
C 2
Figure 6-7. Crystal Block Diagram
Any crystal used with TRF7970A should have minimum characteristics shown in Table 6-9 .
26
Detailed Description
Submit Documentation Feedback
Product Folder Links: TRF7970A
Copyright ? 2011–2014, Texas Instruments Incorporated
相关PDF资料
TRM-418-LT TRANSCEIVER RF 418MHZ LT SERIES
TRM-900-NT RF TXRX 915MHZ NT SERIES
TRX08GVP2540 TXRX OPT SCFF 8.5GB/S 850NM
TS-320240BRNO TCH PANEL 140X104 RESISTIVE MONO
TS-TFT3.5Z TOUCH PANEL 140X1.4.0 TFT
TS3-75B3 SENSOR THERMAL MOXIE NTC 75C
TSL26711FN IC PROXIMITY DETECTOR 6-DFN
TSOP57238TT1 IC IR RCVR MODULE 38KHZ
相关代理商/技术参数
TRF7970ARHBR 功能描述:IC RFID/NFC AFE 13.56MHZ 32QFN RoHS:是 类别:RF/IF 和 RFID >> RFID IC 系列:- 其它有关文件:CR14 View All Specifications 标准包装:1 系列:- RF 型:收发器 频率:13.56MHz 特点:ISO14443-B 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SO 包装:Digi-Reel® 其它名称:497-5719-6
TRF7970ARHBT 功能描述:IC RFID/NFC AFE 13.56MHZ 32QFN RoHS:是 类别:RF/IF 和 RFID >> RFID IC 系列:- 其它有关文件:CR14 View All Specifications 标准包装:1 系列:- RF 型:收发器 频率:13.56MHz 特点:ISO14443-B 封装/外壳:16-SOIC(0.154",3.90mm 宽) 供应商设备封装:16-SO 包装:Digi-Reel® 其它名称:497-5719-6
TRF7970ATB 功能描述:RFID应答器 TRF7970A Target Brd RoHS:否 制造商:Murata 存储容量:512 bit 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
TRF79A6AA17LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA18LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA19LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA20LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)
TRF79A6AA21LB000 制造商:Opnext 功能描述:XFP FORM FACTOR - Boxed Product (Development Kits)